Difference between revisions of "CM-T3730: Linux: Getting started"

From Compulab Mediawiki
Jump to: navigation, search
(Mount the NFS drive)
(Introduction)
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
 +
== Introduction ==
 +
CM-T3730 Linux package supplied with Angstrom and Debian example root filesystem images.
 +
This article provides an introduction on how to install the Angstrom Linux image on CM-T3730.
 +
The Debian image installation can be easily performed by replacing {{filename|angstrom-image-cm-t3730.tar.bz2}} and {{filename|angstrom-image-cm-t3730.ubi}} references by {{filename|debian-image-cm-t3730.tar.bz2}} and {{filename|debian-image-cm-t3730.ubi respectively}} in the installation procedures described below.
 +
 
== Preparation steps ==
 
== Preparation steps ==
* Obtain a Linux PC workstation with a serial communication port.
+
* Obtain a PC workstation with a serial communication port.
 
* For networked installation you need to install a TFTP server on the host PC. For Windows machines we recommend [http://tftpd32.jounin.net/ TFTPD32] included in the Linux package for CM-T3730 (link below).
 
* For networked installation you need to install a TFTP server on the host PC. For Windows machines we recommend [http://tftpd32.jounin.net/ TFTPD32] included in the Linux package for CM-T3730 (link below).
* Download the [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres Linux package for CM-T3730] from CompuLab website. Unzip the package to a directory on your host workstation.
+
* Download the Linux package for CM-T3730 from [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres CompuLab website]. Unzip the package to a directory on your host workstation.
* All image files mentioned below can be found in {{filename|images}} subdirectory.
+
* All image files mentioned below can be found in {{filename|images}} subdirectory
* Connect the host PC to the SB-T35 base-board (connector P12) via the serial cable supplied with the evaluation kit.
+
* Connect the host PC to the SB-T35 base-board (connector P12) via the serial cable supplied with the evaluation kit.  
 
* Start terminal emulation software on your PC. Set baud rate to 115200 bps, 8 bit per frame, 1 stop bit, no parity, no flow control.
 
* Start terminal emulation software on your PC. Set baud rate to 115200 bps, 8 bit per frame, 1 stop bit, no parity, no flow control.
* Turn on the CM-T3730 evaluation system. The U-Boot boot-loader will start and you will get a command prompt.  
+
* Turn on the CM-T3730 evaluation system. The U-Boot boot-loader will start and you will get a command prompt.
 
*: {{Note|If the boot settings of your CM-T3730 are different than default, you may need to press and hold '''Ctrl-C''' while turning the CM-T3730 on, in order to get command prompt.}}
 
*: {{Note|If the boot settings of your CM-T3730 are different than default, you may need to press and hold '''Ctrl-C''' while turning the CM-T3730 on, in order to get command prompt.}}
  
Line 16: Line 21:
  
 
=== Using installation environment on MMC/SD card ===
 
=== Using installation environment on MMC/SD card ===
* Copy {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|bootscr.img}} from [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres Linux package for CM-T3730] to the root directory on the first partition of the MMC/SD card. Note, the partition must be FAT (16 or 32) formated.
+
* Copy {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|bootscr.img}} from [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres Linux package for CM-T3730] to the root directory on the first partition of the MMC/SD card. Note, the partition must be FAT (16 or 32) formatted.
* Insert the MMC/SD card into the SD socket (P13) on the SB-T35.
+
* Insert the MMC/SD card into the micro SD socket (P5) on the CM-T3730 module, or the SD socket (P13) on the SB-T35 depending on your modules configuration.
 
* Use the following U-boot commands to boot the installation environment on the CM-T3730:
 
* Use the following U-boot commands to boot the installation environment on the CM-T3730:
 
<pre>
 
<pre>
Line 24: Line 29:
 
CM-T3x # source 80400000
 
CM-T3x # source 80400000
 
</pre>
 
</pre>
* Continue to the [[#Install Kernel and Angstrom Linux Images | Install Kernel and Angstrom Linux Images]] section.
+
* Continue to the [[#Install Kernel and Angstrom Linux Images | Install Kernel and Angstrom Linux Images]] section.
  
 
=== Using installation environment from TFTP server ===
 
=== Using installation environment from TFTP server ===
* Connect the CM-T3730 Ethernet port (connector P18 on the SB-T35) to your local network.
+
* Connect the CM-T3730 Ethernet port to your local network.
 
* Put {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|bootscr.img}} from [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres Linux package for CM-T3730] to a location accessible by the TFTP server:
 
* Put {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|bootscr.img}} from [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres Linux package for CM-T3730] to a location accessible by the TFTP server:
 
*: - On Windows machine: copy {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|bootscr.img}} to the same folder and point the TFTP server to that folder
 
*: - On Windows machine: copy {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|bootscr.img}} to the same folder and point the TFTP server to that folder
 
*: - On Linux machine: copy {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|bootscr.img}} to TFTP server root directory, usually {{filename|/tftpboot}} or {{filename|/tftproot}}.
 
*: - On Linux machine: copy {{filename|kernel.img}}, {{filename|ramdisk.img}} and {{filename|bootscr.img}} to TFTP server root directory, usually {{filename|/tftpboot}} or {{filename|/tftproot}}.
* You can use U-boot {{cmd|dhcp}} command to obtain IP address or manually set {{parameter|ipaddr}} environment variable:
+
* You can use U-boot {{cmd|dhcp}} command to obtain IP address
 +
<pre>
 +
CM-T3x # dhcp
 +
</pre>
 +
:or manually set {{parameter|ipaddr}} environment variable:
 
<pre>
 
<pre>
 
CM-T3x # setenv ipaddr <CM-T3730 ip address>
 
CM-T3x # setenv ipaddr <CM-T3730 ip address>
Line 44: Line 53:
 
CM-T3x # tftp 80400000 bootscr.img && source 80400000
 
CM-T3x # tftp 80400000 bootscr.img && source 80400000
 
</pre>
 
</pre>
* Continue to the [[#Install Kernel and Angstrom Linux Images | Install Kernel and Angstrom Linux Images]] section.
+
* Continue to the [[#Install Kernel and Angstrom Linux Images | Install Kernel and Angstrom Linux Images]] section.
  
== Install Kernel and Angstrom Linux Images ==
+
=== Install Kernel and Angstrom Linux Images ===
After the ramdisk image is loaded the Linux login prompt will appear. Login as {{parameter|root}} into the system. Use {{parameter|111111}} password for login:
+
After the ramdisk image is loaded the Linux login prompt will appear. Login as {{parameter|root}} into the system.
 
<pre>
 
<pre>
 
compulab login: root
 
compulab login: root
Password: 111111
 
 
</pre>
 
</pre>
The next step is installing the kernel and Angstrom Linux images. The following media can be used as a source for installation:
+
 
* [[#Mount the MMC/SD Card|MMC/SD Card]]
+
==== Mount the installation source media ====
 +
 
 +
The next step is installing the kernel and Angstorm Linux images. The following media can be used as a source for installation:
 +
* [[#Mount an MMC/SD Card|MMC/SD Card]]
 
* [[#Mount a USB Storage Device|USB storage device]]
 
* [[#Mount a USB Storage Device|USB storage device]]
* [[#Mount the NFS drive|NFS drive]]
+
* [[#Mount an NFS drive|NFS drive]]
  
=== Mount an MMC/SD Card ===
+
===== Mount an MMC/SD Card =====
* Copy the {{filename|Angstrom-image-cm-t3730.ubi}} and the {{filename|uImage-cm-t3730.bin}} from the [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres Linux package for CM-T3730] to the root directory of any partition on the MMC/SD card. The partition can be formatted either ext2/3/4 or FAT file system.
+
* Copy the {{filename|angstrom-image-cm-t3730.ubi}} and the {{filename|uImage-cm-t3730}} from the [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres Linux package for CM-T3730] to the root directory of any partition on the MMC/SD card. The partition can be formatted either ext2/3/4 or FAT file system.
 
* Insert the MMC/SD card into the SD socket (P13) on the SB-T35.
 
* Insert the MMC/SD card into the SD socket (P13) on the SB-T35.
 
* The MMC/SD card is mounted automatically under /media/mmcblk0pX. Where X is the partition number.
 
* The MMC/SD card is mounted automatically under /media/mmcblk0pX. Where X is the partition number.
Line 67: Line 78:
 
* Continue to the [[#Install Images | Install Images]] section.
 
* Continue to the [[#Install Images | Install Images]] section.
  
=== Mount a USB Storage Device ===
+
===== Mount a USB Storage Device =====
* Copy the {{filename|Angstrom-image-cm-t3730.ubi}}, the {{filename|Angstrom-image-cm-t3730.tar.bz2}} and the {{filename|uImage-cm-t3730.bin}} from [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres Linux package for CM-T3730] to the root directory of any partition on the USB storage device.
+
* Copy the {{filename| angstrom-image-cm-t3730.ubi}} and the {{filename|uImage-cm-t3730}} from [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres Linux package for CM-T3730] to the root directory of any partition on the USB storage device.
 
* Plug the USB storage device to any port on the dual USB host connector (P17) on the SB-T35.
 
* Plug the USB storage device to any port on the dual USB host connector (P17) on the SB-T35.
 
* The USB device is mounted automatically under /media/sdXY. Where X is the device letter and Y is the partition number.
 
* The USB device is mounted automatically under /media/sdXY. Where X is the device letter and Y is the partition number.
Line 77: Line 88:
 
* Continue to the [[#Install Images | Install Images]] section.
 
* Continue to the [[#Install Images | Install Images]] section.
  
=== Mount an NFS drive ===
+
===== Mount an NFS drive =====
* Connect the CM-T3730 Ethernet port (connector P18 on the SB-T35) to your local network.
+
* Connect the CM-T3730 Ethernet port (connector P16 or P18 on the SB-T35) to your local network.
* Copy the {{filename|Angstrom-image-cm-t3730.ubi}}, the {{filename|Angstrom-image-cm-t3730.tar.bz2}} and the {{filename|uImage-cm-t3730.bin}} from the [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres Linux package for CM-T3730] to a directory exported through NFS.
+
* Copy the {{filename|angstrom-image-cm-t3730.ubi}} and the {{filename|uImage-cm-t3730}} from the [http://compulab.co.il/products/computer-on-modules/cm-t3730/#devres Linux package for CM-T3730] to a directory exported through NFS.
* During Ramdisk image booting the CM-T3730 attempts to obtain an IP address using DHCP. If from some reason the IP address has not been obtained, use the following command to obtain IP address for the CM-T3730:
+
* During Ramdisk image booting the CM-T3730 attempts to obtain an IP address using DHCP. If from some reason the IP address has not been obtained, use the following commands to obtain IP address for the CM-T3730:
** Using DHCP:<pre>root@compulab:~#  ifup `basename /sys/devices/platform/smsc911x.0/net/eth?`</pre>
+
** If P18 Ethernet port is connected (CM-T3730 SMSC Ethernet controller is used): <pre>export eth_device=smsc911x.0</pre>
** If you do not have a DHCP server, you can set a static IP address using {{cmd|ifconfig}}:<pre>root@compulab:~#  ifconfig `basename /sys/devices/platform/smsc911x.0/net/eth?` <ip address></pre>
+
** If P16 Ethernet port is connected (SB-T35 SMSC Ethernet controller is used): <pre>export eth_device=smsc911x.1</pre>
* Mount the NFS share containing the {{filename|uImage-cm-t3730.bin}}, the {{filename|Angstrom-image-cm-t3730.ubi}} and the {{filename|Angstrom-image-cm-t3730.tar.bz2}} files:
+
** Obtain IP using DHCP:<pre>root@compulab:~#  ifup `basename /sys/devices/platform/$eth_device/net/eth?`</pre>
 +
** If you do not have a DHCP server, you can set a static IP address using {{cmd|ifconfig}}:<pre>root@compulab:~#  ifconfig `basename /sys/devices/platform/$eth_device/net/eth?` <ip address></pre>
 +
* Mount the NFS share containing the {{filename|uImage-cm-t3730}} and the {{filename|angstrom-image-cm-t3730.ubi}} files:
 
<pre>
 
<pre>
 
root@compulab:~#  mount -o nolock <host ip>:/path/to/nfs/share /mnt/net
 
root@compulab:~#  mount -o nolock <host ip>:/path/to/nfs/share /mnt/net
Line 89: Line 102:
 
* Continue to [[#Install Images | Install Images]] section.
 
* Continue to [[#Install Images | Install Images]] section.
  
=== Install Images ===
+
==== Install Images ====
 
Once the ramdisk image is loaded and the media containing the CM-T3730 Kernel and Angstrom Linux images is mounted, the installation can be done on either of the following:
 
Once the ramdisk image is loaded and the media containing the CM-T3730 Kernel and Angstrom Linux images is mounted, the installation can be done on either of the following:
 
* [[#Install on the NAND flash|NAND Flash]]
 
* [[#Install on the NAND flash|NAND Flash]]
 
* [[#Install on the Micro SD Card|Micro SD Card]]
 
* [[#Install on the Micro SD Card|Micro SD Card]]
  
==== Install on the NAND flash ====
+
===== Install on the NAND flash =====
* In this subsection the term {{filename|/mount/point}} can be:
+
The installation on the NAND flash can be done using the mounted media containing the CM-T3730 Kernel and Angstorm Linux images.
 +
 
 +
* In this section the term {{filename|/mount/point}} can be either of the following:
 
** {{filename|/media/mmcblk0pX}} if MMC/SD card is used, where X is the partition number.
 
** {{filename|/media/mmcblk0pX}} if MMC/SD card is used, where X is the partition number.
 
** {{filename|/media/sdXY}} if USB storage is used, where X is the USB drive letter and Y is the partition number.
 
** {{filename|/media/sdXY}} if USB storage is used, where X is the USB drive letter and Y is the partition number.
 +
** {{filename|/mnt/net}} if NFS drive is used.
 +
 
* Format the NAND flash kernel partition and write the kernel image onto it:
 
* Format the NAND flash kernel partition and write the kernel image onto it:
 
<pre>
 
<pre>
$ flash_erase /dev/mtd3 0 0
+
root@compulab:~# flash_erase /dev/mtd3 0 0
$ nandwrite -p /dev/mtd3 /mount/point/uImage-cm-t3730.bin
+
root@compulab:~# nandwrite -p /dev/mtd3 /mount/point/uImage-cm-t3730
 
</pre>
 
</pre>
* Format the NAND flash root filesystem partition and write the Angstrom filesystem image onto it:
+
* Format the NAND flash root filesystem partition and write Angstorm filesystem image onto it:
 
<pre>
 
<pre>
$ ubiformat -O 2048 /dev/mtd4 -f /mount/point/Angstrom-image-cm-t3730.ubi
+
root@compulab:~# ubiformat -O 2048 /dev/mtd4 -f /mount/point/angstrom-image-cm-t3730.ubi
 
</pre>
 
</pre>
 
* Continue to the [[#After Installation | After Installation]] section.
 
* Continue to the [[#After Installation | After Installation]] section.
  
==== Install on the Micro SD Card ====
+
===== Install on the Micro SD Card =====
 
* In this subsection the term {{filename|/mount/point}} can be:
 
* In this subsection the term {{filename|/mount/point}} can be:
 
** {{filename|/mnt/net}} if NFS is used
 
** {{filename|/mnt/net}} if NFS is used
Line 118: Line 135:
 
1
 
1
 
</pre>
 
</pre>
* Copy the {{filename|uImage-cm-t3730.bin}} to the micro SD card first (FAT) partition and name it {{filename|uImage-cm-t3730}}:
+
* Copy the {{filename|uImage-cm-t3730}} to the micro SD card first (FAT) partition:
 
<pre>
 
<pre>
root@compulab:~# cp /mount/point/uImage-cm-t3730.bin /media/mmcblk0p1/uImage-cm-t3730
+
root@compulab:~# cp /mount/point/uImage-cm-t3730 /media/mmcblk0p1/
 
</pre>
 
</pre>
 
* Unmount the micro SD card first (FAT) partition
 
* Unmount the micro SD card first (FAT) partition
Line 128: Line 145:
 
* Create an additional partition for the Linux file system on the micro SD card:
 
* Create an additional partition for the Linux file system on the micro SD card:
 
<pre>
 
<pre>
root@compulab:~# fdisk /dev/mmcblk0 << eof
+
root@compulab:~# echo -e "n\np\n2\n\n\nw\neof\n" | fdisk /dev/mmcblk0
> n
 
> p
 
> 2
 
> 239
 
>
 
> w
 
> eof
 
 
 
The number of cylinders for this disk is set to 15318.
 
There is nothing wrong with that, but this is larger than 1024,
 
and could in certain setups cause problems with:
 
1) software that runs at boot time (e.g., old versions of LILO)
 
2) booting and partitioning software from other OSs
 
  (e.g., DOS FDISK, OS/2 FDISK)
 
 
 
Command (m for help): Command action
 
  e  extended
 
  p  primary partition (1-4)
 
Partition number (1-4): First cylinder (1-15318, default 1): Last cylinder or +size or +sizeM or +sizeK (239-15318, default 15318): Using default value 15318
 
 
 
Command (m for help): The partition table has been altered.
 
Calling ioctl() to re-read partition table
 
mmcblk0: p1 p2
 
 
</pre>
 
</pre>
 
* Format the new partition with ext4 filesystem:
 
* Format the new partition with ext4 filesystem:
Line 159: Line 153:
 
* Mount the new micro SD card partition:
 
* Mount the new micro SD card partition:
 
<pre>
 
<pre>
root@compulab:~# mkdir -p /media/rootfs && mount /dev/mmcblk0p2 /media/rootfs/
+
root@compulab:~# mkdir -p /media/mmcblk0p2 && mount /dev/mmcblk0p2 /media/mmcblk0p2/
 
</pre>
 
</pre>
* Extract the content of {{filename|Angstrom-image-cm-t3730.tar.bz2}} onto that partition:
+
* Extract the content of {{filename|angstrom-image-cm-t3730.tar.bz2}} onto that partition:
 
<pre>
 
<pre>
root@compulab:~# tar -xvpf /mount/point/Angstrom-image-cm-t3730.tar.bz2 -C /media/rootfs && sync
+
root@compulab:~# tar -xvpf /mount/point/angstrom-image-cm-t3730.tar.bz2 -C /media/mmcblk0p2 && sync
 
</pre>
 
</pre>
 
* Continue to the [[#After Installation | After Installation]] section.
 
* Continue to the [[#After Installation | After Installation]] section.
  
 
== Install Images on the micro SD Card using Linux Host workstation ==
 
== Install Images on the micro SD Card using Linux Host workstation ==
 +
Installation of Linux kernel and Angstrom user space on micro SD card can be also performed using Linux Host workstation.
 +
 
* Obtain a Linux PC workstation with a micro SD card reader.
 
* Obtain a Linux PC workstation with a micro SD card reader.
* The micro SD card, supplied with the CM-T3730 Evaluation kit, has already been pre-partitioned as described in the [[CM-T3x: U-Boot: Firmware Overview#Default MMC/SD card mapping|CM-T3x: U-Boot: Firmware Overview]] article.
+
* Micro SD card must be prepared as described in the [[CM-T3x: U-Boot: Firmware Overview#Default MMC/SD card mapping|CM-T3x: U-Boot: Firmware Overview]] article. Micro SD card, supplied with the CM-T3730 Evaluation kit, already contains first (FAT) partition with the bootloader.
 
* Plug the micro SD card, supplied with the CM-T3730 Evaluation kit, into the micro SD card reader attached to the desktop workstation.
 
* Plug the micro SD card, supplied with the CM-T3730 Evaluation kit, into the micro SD card reader attached to the desktop workstation.
 
* Depending on the desktop system setup, following steps might require super user privileges.
 
* Depending on the desktop system setup, following steps might require super user privileges.
Line 177: Line 173:
 
sudo mkdir -p /media/boot && sudo mount /dev/sde1 /media/boot/
 
sudo mkdir -p /media/boot && sudo mount /dev/sde1 /media/boot/
 
</pre>
 
</pre>
* Copy the {{filename|uImage-cm-t3730.bin}} to the micro SD card first (FAT) partition and name it {{filename|uImage-cm-t3730}}:
+
* Copy the {{filename|uImage-cm-t3730}} to the micro SD card first (FAT) partition:
 +
<pre>
 +
sudo cp cm-t3730-linux/images/uImage-cm-t3730 /media/boot/
 +
</pre>
 +
 
 +
* Unmount the micro SD card first (FAT) partition
 +
<pre>
 +
sudo umount /dev/sde1
 +
</pre>
 +
* Create an additional partition for the Linux file system on the micro SD card:
 
<pre>
 
<pre>
sudo cp cm-t3730-linux/images/uImage-cm-t3730.bin /media/boot/uImage-cm-t3730
+
echo -e "n\np\n2\n\n\nw\neof\n" | sudo fdisk /dev/sde -u=cylinders
 
</pre>
 
</pre>
 
* Format the second micro SD card partition with ext4 filesystem:
 
* Format the second micro SD card partition with ext4 filesystem:
Line 189: Line 194:
 
sudo mkdir -p /media/rootfs && sudo mount /dev/sde2 /media/rootfs/
 
sudo mkdir -p /media/rootfs && sudo mount /dev/sde2 /media/rootfs/
 
</pre>
 
</pre>
* Extract the content of the {{filename|Angstrom-image-cm-t3730.tar.bz2}} onto that partition:
+
* Extract the content of the {{filename|angstrom-image-cm-t3730.tar.bz2}} onto that partition:
 
<pre>
 
<pre>
sudo tar -xpvf cm-t3730-linux/images/Angstrom-image-cm-t3730.tar.bz2 -C /media/rootfs && sync
+
sudo tar -xpvf cm-t3730-linux/images/angstrom-image-cm-t3730.tar.bz2 -C /media/rootfs && sync
 
</pre>
 
</pre>
 
* Unmount all micro SD card partitions:
 
* Unmount all micro SD card partitions:
Line 201: Line 206:
  
 
== After Installation ==
 
== After Installation ==
* Make sure there is no MMC/SD card in the SD socket (P13) on the SB-T35.
+
* Make sure there is no MMC/SD card in the SD socket (P13) on SB-T35.
 
* Reset the system.
 
* Reset the system.
{{Note|If the boot settings of the CM-T3730 are different than default, you may need to press and hold '''Ctrl-C''' while turning the CM-T3730 on, in order to get command prompt.}}
+
*: {{Note|If the boot settings of your CM-T3730 are different than default, you may need to press and hold ^C while turning the CM-T3730 on, in order to get command prompt.}}
 +
 
 
* CM-T3730 will boot Angstrom Linux from the internal NAND flash or the micro SD card.
 
* CM-T3730 will boot Angstrom Linux from the internal NAND flash or the micro SD card.
{{Note|The first boot might take longer time because Angstrom Linux performs a lot of one-time initialization tasks.}}
+
*: {{Note|The first boot might take longer time because Angstrom Linux performs a lot of one-time initialization tasks.}}
  
 
=== Boot from the NAND flash ===
 
=== Boot from the NAND flash ===
 
* Set the {{parameter|bootargs}} environment variable:
 
* Set the {{parameter|bootargs}} environment variable:
 
<pre>
 
<pre>
CM-T3x # setenv bootargs 'ubi.mtd=4,2048 root=ubi0:rootfs rw rootfstype=ubifs console=ttyO2,115200 \
+
CM-T3x # setenv bootargs 'ubi.mtd=rootfs,2048 root=ubi0:rootfs rw rootfstype=ubifs console=ttyO2,115200n8'
omapfb.mode=dvi:1024x768-24@60 omapfb.vram=1:4M vram=8M omapdss.def_disp=dvi ip=dhcp'
 
 
</pre>
 
</pre>
 
* To boot Linux, type:
 
* To boot Linux, type:
 +
<pre>CM-T3x # nboot 82000000 nand0 2a0000; bootm</pre>
 +
 +
{{Note|The Linux kernel for CM-T3730 is shipped with built-in command line parameters. Setting U-Boot {{parameter|bootargs}} environment variable overrides default kernel command line.}}
 +
 +
* For Linux automatic boot, type:
 
<pre>
 
<pre>
 
CM-T3x # setenv bootdelay 3
 
CM-T3x # setenv bootdelay 3
Line 224: Line 234:
 
* Reset the system.
 
* Reset the system.
 
* The boot from micro SD card will start automatically with default U-Boot environment.
 
* The boot from micro SD card will start automatically with default U-Boot environment.
 +
 +
=== Configure video output ===
 +
 +
==== Select LCD model ====
 +
 +
CM-T3730 Evaluation Kit can be equipped with either of the following LCD panels: Toppoly TDO35S or DataImage SCF0403852GGU04.
 +
Toppoly TDO35S is registered as default OMAP DSS LCD device.
 +
 +
To set DataImage LCD as OMAP DSS LCD device add the following boot option to the kernel command line parameters:
 +
<pre>
 +
cm_t3x_lcd=dataimage
 +
</pre>
 +
 +
==== Select video out ====
 +
 +
Default CM-T3730 video output device is LCD. Other video output devices can be used as well:
 +
* DVI output can be enabled by adding the following boot options to the kernel command line parameters:
 +
<pre>
 +
omapfb.vram=1:4M vram=8M omapfb.mode=dvi:1024x768-24@60 omapdss.def_disp=dvi
 +
</pre>
 +
* TV output can be enabled by adding the following boot options to the kernel command line parameters:
 +
<pre>
 +
omapfb.mode=tv:ntsc omapdss.def_disp=tv
 +
</pre>
  
 
== See also ==
 
== See also ==
 +
 
* [[CM-T3730: Linux: Angstrom]]
 
* [[CM-T3730: Linux: Angstrom]]
 +
* [[CM-T3730: Linux: Debian]]
 
* [[CM-T3730: Linux: Kernel]]
 
* [[CM-T3730: Linux: Kernel]]
 
* [[Linux Development for ARM modules]]
 
* [[Linux Development for ARM modules]]
 
* [[U-Boot for CM-T3730]]
 
* [[U-Boot for CM-T3730]]
 +
* [[CM-T3x: U-Boot: Firmware Overview#Default MMC/SD card mapping|Default MMC/SD card mapping]]
  
 
[[Category:Linux|Getting started]]
 
[[Category:Linux|Getting started]]
 
[[Category:CM-T3730|Linux: Getting started]]
 
[[Category:CM-T3730|Linux: Getting started]]

Latest revision as of 12:36, 16 February 2014

Introduction

CM-T3730 Linux package supplied with Angstrom and Debian example root filesystem images. This article provides an introduction on how to install the Angstrom Linux image on CM-T3730. The Debian image installation can be easily performed by replacing angstrom-image-cm-t3730.tar.bz2 and angstrom-image-cm-t3730.ubi references by debian-image-cm-t3730.tar.bz2 and debian-image-cm-t3730.ubi respectively in the installation procedures described below.

Preparation steps

  • Obtain a PC workstation with a serial communication port.
  • For networked installation you need to install a TFTP server on the host PC. For Windows machines we recommend TFTPD32 included in the Linux package for CM-T3730 (link below).
  • Download the Linux package for CM-T3730 from CompuLab website. Unzip the package to a directory on your host workstation.
  • All image files mentioned below can be found in images subdirectory
  • Connect the host PC to the SB-T35 base-board (connector P12) via the serial cable supplied with the evaluation kit.
  • Start terminal emulation software on your PC. Set baud rate to 115200 bps, 8 bit per frame, 1 stop bit, no parity, no flow control.
  • Turn on the CM-T3730 evaluation system. The U-Boot boot-loader will start and you will get a command prompt.
Admolition note.png If the boot settings of your CM-T3730 are different than default, you may need to press and hold Ctrl-C while turning the CM-T3730 on, in order to get command prompt.

Boot into the installation environment (ramdisk)

The first step in CM-T3730 Linux installation is starting the installation environment (Linux kernel and Ramdisk image). This can be done using the following media:

Using installation environment on MMC/SD card

  • Copy kernel.img, ramdisk.img and bootscr.img from Linux package for CM-T3730 to the root directory on the first partition of the MMC/SD card. Note, the partition must be FAT (16 or 32) formatted.
  • Insert the MMC/SD card into the micro SD socket (P5) on the CM-T3730 module, or the SD socket (P13) on the SB-T35 depending on your modules configuration.
  • Use the following U-boot commands to boot the installation environment on the CM-T3730:
CM-T3x # mmc rescan
CM-T3x # fatload mmc 0:1 80400000 bootscr.img
CM-T3x # source 80400000

Using installation environment from TFTP server

  • Connect the CM-T3730 Ethernet port to your local network.
  • Put kernel.img, ramdisk.img and bootscr.img from Linux package for CM-T3730 to a location accessible by the TFTP server:
    - On Windows machine: copy kernel.img, ramdisk.img and bootscr.img to the same folder and point the TFTP server to that folder
    - On Linux machine: copy kernel.img, ramdisk.img and bootscr.img to TFTP server root directory, usually /tftpboot or /tftproot.
  • You can use U-boot dhcp command to obtain IP address
CM-T3x # dhcp
or manually set ipaddr environment variable:
CM-T3x # setenv ipaddr <CM-T3730 ip address>
  • Set serverip environment variable and save the new environment:
CM-T3x # setenv serverip <host ip address>
CM-T3x # saveenv
  • Use the following U-boot command to boot Linux on CM-T3730:
CM-T3x # tftp 80400000 bootscr.img && source 80400000

Install Kernel and Angstrom Linux Images

After the ramdisk image is loaded the Linux login prompt will appear. Login as root into the system.

compulab login: root

Mount the installation source media

The next step is installing the kernel and Angstorm Linux images. The following media can be used as a source for installation:

Mount an MMC/SD Card
  • Copy the angstrom-image-cm-t3730.ubi and the uImage-cm-t3730 from the Linux package for CM-T3730 to the root directory of any partition on the MMC/SD card. The partition can be formatted either ext2/3/4 or FAT file system.
  • Insert the MMC/SD card into the SD socket (P13) on the SB-T35.
  • The MMC/SD card is mounted automatically under /media/mmcblk0pX. Where X is the partition number.
  • If for some reason the MMC/SD card hasn't been mounted automatically, use the following mount command:
root@compulab:~# mkdir -p /media/mmcblk0pX && mount /dev/mmcblk0pX /media/mmcblk0pX
Mount a USB Storage Device
  • Copy the angstrom-image-cm-t3730.ubi and the uImage-cm-t3730 from Linux package for CM-T3730 to the root directory of any partition on the USB storage device.
  • Plug the USB storage device to any port on the dual USB host connector (P17) on the SB-T35.
  • The USB device is mounted automatically under /media/sdXY. Where X is the device letter and Y is the partition number.
  • If for some reason the USB storage device hasn't been mounted automatically, use the following mount command:
root@compulab:~# mkdir -p /media/sdXY && mount /dev/sdXY /media/sdXY
Mount an NFS drive
  • Connect the CM-T3730 Ethernet port (connector P16 or P18 on the SB-T35) to your local network.
  • Copy the angstrom-image-cm-t3730.ubi and the uImage-cm-t3730 from the Linux package for CM-T3730 to a directory exported through NFS.
  • During Ramdisk image booting the CM-T3730 attempts to obtain an IP address using DHCP. If from some reason the IP address has not been obtained, use the following commands to obtain IP address for the CM-T3730:
    • If P18 Ethernet port is connected (CM-T3730 SMSC Ethernet controller is used):
      export eth_device=smsc911x.0
    • If P16 Ethernet port is connected (SB-T35 SMSC Ethernet controller is used):
      export eth_device=smsc911x.1
    • Obtain IP using DHCP:
      root@compulab:~#  ifup `basename /sys/devices/platform/$eth_device/net/eth?`
    • If you do not have a DHCP server, you can set a static IP address using ifconfig:
      root@compulab:~#  ifconfig `basename /sys/devices/platform/$eth_device/net/eth?` <ip address>
  • Mount the NFS share containing the uImage-cm-t3730 and the angstrom-image-cm-t3730.ubi files:
root@compulab:~#  mount -o nolock <host ip>:/path/to/nfs/share /mnt/net

Install Images

Once the ramdisk image is loaded and the media containing the CM-T3730 Kernel and Angstrom Linux images is mounted, the installation can be done on either of the following:

Install on the NAND flash

The installation on the NAND flash can be done using the mounted media containing the CM-T3730 Kernel and Angstorm Linux images.

  • In this section the term /mount/point can be either of the following:
    • /media/mmcblk0pX if MMC/SD card is used, where X is the partition number.
    • /media/sdXY if USB storage is used, where X is the USB drive letter and Y is the partition number.
    • /mnt/net if NFS drive is used.
  • Format the NAND flash kernel partition and write the kernel image onto it:
root@compulab:~# flash_erase /dev/mtd3 0 0
root@compulab:~# nandwrite -p /dev/mtd3 /mount/point/uImage-cm-t3730
  • Format the NAND flash root filesystem partition and write Angstorm filesystem image onto it:
root@compulab:~# ubiformat -O 2048 /dev/mtd4 -f /mount/point/angstrom-image-cm-t3730.ubi
Install on the Micro SD Card
  • In this subsection the term /mount/point can be:
    • /mnt/net if NFS is used
    • /media/sdXY if USB storage is used, where X is the USB drive letter and Y is the partition number.
  • Make sure the micro SD card first (FAT) partition is mounted under the /media/mmcblk0p1:
root@compulab:~# cat /proc/mounts | grep -c mmcblk0p1
1
  • Copy the uImage-cm-t3730 to the micro SD card first (FAT) partition:
root@compulab:~# cp /mount/point/uImage-cm-t3730 /media/mmcblk0p1/
  • Unmount the micro SD card first (FAT) partition
root@compulab:~# umount /dev/mmcblk0p1
  • Create an additional partition for the Linux file system on the micro SD card:
root@compulab:~# echo -e "n\np\n2\n\n\nw\neof\n" | fdisk /dev/mmcblk0
  • Format the new partition with ext4 filesystem:
root@compulab:~# mkfs.ext4 /dev/mmcblk0p2
  • Mount the new micro SD card partition:
root@compulab:~# mkdir -p /media/mmcblk0p2 && mount /dev/mmcblk0p2 /media/mmcblk0p2/
  • Extract the content of angstrom-image-cm-t3730.tar.bz2 onto that partition:
root@compulab:~# tar -xvpf /mount/point/angstrom-image-cm-t3730.tar.bz2 -C /media/mmcblk0p2 && sync

Install Images on the micro SD Card using Linux Host workstation

Installation of Linux kernel and Angstrom user space on micro SD card can be also performed using Linux Host workstation.

  • Obtain a Linux PC workstation with a micro SD card reader.
  • Micro SD card must be prepared as described in the CM-T3x: U-Boot: Firmware Overview article. Micro SD card, supplied with the CM-T3730 Evaluation kit, already contains first (FAT) partition with the bootloader.
  • Plug the micro SD card, supplied with the CM-T3730 Evaluation kit, into the micro SD card reader attached to the desktop workstation.
  • Depending on the desktop system setup, following steps might require super user privileges.
  • The following steps assume that the micro SD card is /dev/sde (this might change depending on the desktop system setup) and the desktop system used does not perform automount.
  • Mount the first (boot) partition of the micro SD card:
sudo mkdir -p /media/boot && sudo mount /dev/sde1 /media/boot/
  • Copy the uImage-cm-t3730 to the micro SD card first (FAT) partition:
sudo cp cm-t3730-linux/images/uImage-cm-t3730 /media/boot/
  • Unmount the micro SD card first (FAT) partition
sudo umount /dev/sde1
  • Create an additional partition for the Linux file system on the micro SD card:
echo -e "n\np\n2\n\n\nw\neof\n" | sudo fdisk /dev/sde -u=cylinders
  • Format the second micro SD card partition with ext4 filesystem:
sudo mkfs.ext4 /dev/sde2
  • Mount the second micro SD card partition:
sudo mkdir -p /media/rootfs && sudo mount /dev/sde2 /media/rootfs/
  • Extract the content of the angstrom-image-cm-t3730.tar.bz2 onto that partition:
sudo tar -xpvf cm-t3730-linux/images/angstrom-image-cm-t3730.tar.bz2 -C /media/rootfs && sync
  • Unmount all micro SD card partitions:
sudo umount /dev/sde1; sudo umount /dev/sde2
  • Remove the micro SD card from the SD card reader and install it in the CM-T3730 micro SD card socket (P5).
  • Continue to the After Installation section.

After Installation

  • Make sure there is no MMC/SD card in the SD socket (P13) on SB-T35.
  • Reset the system.
Admolition note.png If the boot settings of your CM-T3730 are different than default, you may need to press and hold ^C while turning the CM-T3730 on, in order to get command prompt.
  • CM-T3730 will boot Angstrom Linux from the internal NAND flash or the micro SD card.
Admolition note.png The first boot might take longer time because Angstrom Linux performs a lot of one-time initialization tasks.

Boot from the NAND flash

  • Set the bootargs environment variable:
CM-T3x # setenv bootargs 'ubi.mtd=rootfs,2048 root=ubi0:rootfs rw rootfstype=ubifs console=ttyO2,115200n8'
  • To boot Linux, type:
CM-T3x # nboot 82000000 nand0 2a0000; bootm


Admolition note.png The Linux kernel for CM-T3730 is shipped with built-in command line parameters. Setting U-Boot bootargs environment variable overrides default kernel command line.
  • For Linux automatic boot, type:
CM-T3x # setenv bootdelay 3
CM-T3x # setenv bootcmd "nboot 82000000 nand0 2a0000; bootm"
CM-T3x # saveenv
CM-T3x # boot

Boot from the Micro SD Card

  • Reset the system.
  • The boot from micro SD card will start automatically with default U-Boot environment.

Configure video output

Select LCD model

CM-T3730 Evaluation Kit can be equipped with either of the following LCD panels: Toppoly TDO35S or DataImage SCF0403852GGU04. Toppoly TDO35S is registered as default OMAP DSS LCD device.

To set DataImage LCD as OMAP DSS LCD device add the following boot option to the kernel command line parameters:

cm_t3x_lcd=dataimage

Select video out

Default CM-T3730 video output device is LCD. Other video output devices can be used as well:

  • DVI output can be enabled by adding the following boot options to the kernel command line parameters:
omapfb.vram=1:4M vram=8M omapfb.mode=dvi:1024x768-24@60 omapdss.def_disp=dvi
  • TV output can be enabled by adding the following boot options to the kernel command line parameters:
omapfb.mode=tv:ntsc omapdss.def_disp=tv

See also