Difference between revisions of "CL-SOM-iMX8Plus: Yocto Linux: Manual Installation: SD card"
(Created page with "== Introduction == This article provides instructions needed to install the Yocto Linux SD-card image on SD card using a Linux Host workstation. The image provides full boot...") |
|||
(One intermediate revision by the same user not shown) | |||
Line 6: | Line 6: | ||
* Obtain a Linux PC workstation. | * Obtain a Linux PC workstation. | ||
* Obtain a USB Card reader and an micro-SD Card. Any commercially available micro-SD card of 4GB (or larger) may be used for the installation. | * Obtain a USB Card reader and an micro-SD Card. Any commercially available micro-SD card of 4GB (or larger) may be used for the installation. | ||
− | * Download the SOM-iMX8M-Plus Yocto Linux package from [https://www.compulab.com/products/computer-on-modules/som- | + | * Download the SOM-iMX8M-Plus Yocto Linux package from [https://www.compulab.com/products/computer-on-modules/cl-som-imx8plus-nxp-i-mx-8m-plus-system-on-module-computer/#devres CompuLab website]. |
* Unzip the package to a directory on the host workstation. From now we assume the device name is {{filename|pakage_dir}}. | * Unzip the package to a directory on the host workstation. From now we assume the device name is {{filename|pakage_dir}}. | ||
* The Yocto Linux SD-card image file, mentioned below, can be found in the {{filename|images}} subdirectory. | * The Yocto Linux SD-card image file, mentioned below, can be found in the {{filename|images}} subdirectory. | ||
Line 17: | Line 17: | ||
== Run Yocto Linux image == | == Run Yocto Linux image == | ||
− | * Insert the micro-SD card into SD socket '''P23''' | + | * Insert the micro-SD card into SD socket '''P23''' |
− | * Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector '''P13''' | + | * Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector '''P13''' |
− | *: Use a terminal emulator as described [[SOM- | + | *: Use a terminal emulator as described [[CL-SOM-iMX8Plus:_Evaluation_Kit:_Getting_Started#System setup|here]] |
− | * Press and hold the ALT_BOOT button ('''SW7''') and then reset / power-on the system to force boot from SD card | + | * Press and hold the ALT_BOOT button ('''SW7''') and then reset / power-on the system to force boot from SD card. Release ALT_BOOT button after 2-3 seconds |
* The system boots into Linux | * The system boots into Linux | ||
[[Category:Linux]] | [[Category:Linux]] | ||
[[Category:Yocto]] | [[Category:Yocto]] | ||
− | [[Category:SOM- | + | [[Category:CL-SOM-iMX8Plus]] |
Latest revision as of 12:57, 29 December 2022
Introduction
This article provides instructions needed to install the Yocto Linux SD-card image on SD card using a Linux Host workstation. The image provides full boot system including U-Boot, Linux kernel, device driver modules and example root filesystem.
Preparation steps
- Obtain a Linux PC workstation.
- Obtain a USB Card reader and an micro-SD Card. Any commercially available micro-SD card of 4GB (or larger) may be used for the installation.
- Download the SOM-iMX8M-Plus Yocto Linux package from CompuLab website.
- Unzip the package to a directory on the host workstation. From now we assume the device name is pakage_dir.
- The Yocto Linux SD-card image file, mentioned below, can be found in the images subdirectory.
- Plug the USB SD Card reader into the host PC. Insert the micro-SD Card into the USB Card reader. From now we assume the device name of the MMC/SD card on your Linux PC is /dev/sdX.
Installation
- Flash the image file to the micro-SD card:
bzcat pakage_dir/images/imx-image-full-som-imx8m-plus.rootfs.wic.bz2 | sudo dd of=/dev/sdX bs=1M
Run Yocto Linux image
- Insert the micro-SD card into SD socket P23
- Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector P13
- Use a terminal emulator as described here
- Press and hold the ALT_BOOT button (SW7) and then reset / power-on the system to force boot from SD card. Release ALT_BOOT button after 2-3 seconds
- The system boots into Linux