UCM-iMX93: Evaluation Kit: Getting Started - Revision history

Igor at 17:05, 28 January 2026

2026-01-28T17:05:18Z

Igor at 13:14, 19 December 2023

2023-12-19T13:14:50Z

Igor at 11:30, 25 July 2023

2023-07-25T11:30:10Z

Benjamin at 10:26, 19 June 2023

2023-06-19T10:26:22Z

Igor at 07:19, 13 June 2023

2023-06-13T07:19:47Z

Igor: Created page with "link= == System setup == UCM-iMX93 evaluation kit is preloaded with the UCM-iMX93 Yocto Linux image. # Make..."

2023-05-29T14:19:16Z

Created page with "frameless|top|1500px|link= == System setup == UCM-iMX93 evaluation kit is preloaded with the UCM-iMX93 Yocto Linux image. # Make..."

New page

[[Image:UCM-iMX93-eval-kit-quick-setup.png|frameless|top|1500px|link=]]

== System setup ==
UCM-iMX93 evaluation kit is preloaded with the UCM-iMX93 Yocto Linux image.
# Make sure jumper '''E9''' is populated (default state).
# Make sure jumpers '''E2''' and '''E7''' are not populated (default state).
# Connect the LCD panel (included in the kit) to connectors '''P11''' and '''P12'''. Ensure that the flat cables are fully inserted.
# Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector '''P16'''.
# On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings:
<blockquote>
{{:SB-SOM: serial port parameters table}}
</blockquote>

== Starting the system ==
# Connect the DC 12V power supply adapter (included) to main DC power connector '''J4'''.
# Follow the messages in your terminal emulator program until you see the linux shell command line prompt.
{{note|In case no messages appear in your terminal emulation program, please refer to the detailed [[SB-UCM-iMX8: HOWTO: USB Console|USB console]] guide.}}

== What's Next? ==
* [https://www.compulab.com/products/computer-on-modules/ucm-imx93-nxp-i-mx9-som-system-on-module-computer/#devres UCM-iMX93 development resources]

[[Category:UCM-iMX93]]

@@ Line 1: / Line 1: @@
-[[Image:UCM-iMX93-eval-kit-quick-setup.png|frameless|top|1500px|link=]]
+__NOTOC__
 == Package content ==
@@ Line 9: / Line 10: @@
 # Make sure jumper '''E9''' is populated (default state).
 # Make sure jumpers '''E2''' and '''E7''' are not populated (default state).
-# Connect the LCD panel (included in the kit) to connectors '''P11''' and '''P12'''. Ensure that the flat cables are fully inserted.
+# Optional - connect the LCD panel (if ordered with the kit) to connectors '''P7''' and '''P8'''. Ensure that the flat cables are fully inserted.
 # Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector '''P16'''.
 # On your computer, start a terminal emulation program (such as Tera Term or PuTTy) with the following serial port settings:

@@ Line 3: / Line 3: @@
 == Package content ==
-[https://www.compulab.com/wp-content/uploads/2023/06/ucm-imx93_eval-kit-content.pdf Package content list]
+[https://www.compulab.com/wp-content/uploads/2023/07/ucm-imx93_eval-kit-content.pdf Package content list]
 == System setup ==

← Older revision		Revision as of 10:26, 19 June 2023
Line 1:		Line 1:
	[[Image:UCM-iMX93-eval-kit-quick-setup.png\|frameless\|top\|1500px\|link=]]		[[Image:UCM-iMX93-eval-kit-quick-setup.png\|frameless\|top\|1500px\|link=]]
		+
		+	== Package content ==
		+
		+	[https://www.compulab.com/wp-content/uploads/2023/06/ucm-imx93_eval-kit-content.pdf Package content list]

	== System setup ==		== System setup ==

@@ Line 19: / Line 19: @@
 == Starting the system ==
 # Connect the DC 12V power supply adapter (included) to main DC power connector '''J4'''.
 # Follow the messages in your terminal emulator program until you see the linux shell command line prompt.
 {{note|In case no messages appear in your terminal emulation program, please refer to the detailed [[SB-UCM-iMX8: HOWTO: USB Console|USB console]] guide.}}

@@ Line 7: / Line 7: @@
 # Connect the LCD panel (included in the kit) to connectors '''P11''' and '''P12'''. Ensure that the flat cables are fully inserted.
 # Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector '''P16'''.
-# On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings:
+# On your computer, start a terminal emulation program (such as Tera Term or PuTTy) with the following serial port settings:
 <blockquote>
 {{:SB-SOM: serial port parameters table}}