UCM-iMX8M-Plus: Evaluation Kit: Getting Started - Revision history

Igor at 13:52, 5 August 2024

2024-08-05T13:52:02Z

Igor at 13:47, 19 December 2023

2023-12-19T13:47:25Z

imported>Igor.vaisbein: Created page with "link= == System setup == UCM-iMX8M-Plus evaluation kit is preloaded with Yocto Linux image for UCM-iMX8..."

2021-06-07T14:48:54Z

Created page with "frameless|top|1400px|link= == System setup == UCM-iMX8M-Plus evaluation kit is preloaded with Yocto Linux image for UCM-iMX8..."

New page

[[Image:UCM-iMX8M-Plus-eval-kit-quick-setup.png|frameless|top|1400px|link=]]

== System setup ==
UCM-iMX8M-Plus evaluation kit is preloaded with Yocto Linux image for UCM-iMX8M-Plus.
# Make sure jumpers '''E6''' and '''E9''' are populated (default state).
# Make sure jumpers '''E20''' is removed (default state).
# Connect the LCD panel (included in the kit) to connectors '''P22''' and '''P45'''. Ensure that the flat cables are fully inserted.
# Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector '''P13'''.
# On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings:
<blockquote>
{{:SB-SOM: serial port parameters table}}
</blockquote>

== Starting the system ==
# Connect the DC 12V power supply adapter (included) to main DC power connector '''J2'''.
# Follow the messages in your terminal emulator program until you see the linux shell command line prompt.
{{note|In case of no messages appear in your terminal emulation program, please refer to the detailed [[SB-UCM-iMX8: HOWTO: USB Console|USB console]] guide.}}

== What Next? ==
* [[UCM-iMX8M-Plus NXP iMX8M-Plus Yocto Linux|UCM-iMX8M-Plus Yocto guide]]
* [https://www.compulab.com/products/computer-on-modules/ucm-imx8m-plus-nxp-i-mx-8m-plus-som-system-on-module-computer/#devres UCM-iMX8M-Plus development resources]

[[Category:UCM-iMX8M-Plus]]

@@ Line 1: / Line 1: @@
-[[Image:UCM-iMX8Plus-eval-kit-quick-setup.png|frameless|top|1600px|link=]]
+[[Image:UCM-iMX8M-Plus-eval-kit-getting-started.png|frameless|top|1400px|link=]]
 == System setup ==
-UCM-iMX8Plus evaluation kit is preloaded with UCM-iMX8Plus Yocto Linux image.
+UCM-iMX8M-Plus evaluation kit is preloaded with UCM-iMX8M-Plus Yocto Linux image.
-# Make sure jumpers '''E6''' and '''E9''' are populated (default state).
+# Make sure jumper '''E5''' is populated (default state).
-# Make sure jumpers '''E20''' is removed (default state).
+# Make sure jumper '''E3''' is removed (default state).
-# Optional - connect the LCD panel (if ordered with the kit) to connectors '''P11''' and '''P5'''. Ensure that the flat cables are fully inserted.
+# Make sure that the main power switch SW1 is in the OFF position.
-# Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector '''P13'''.
+# For kits ordered with LCD panel: use the EB-HDRLVDS adapter to connect the LCD panel (if ordered with the kit) to connectors '''P13''' and '''P14'''.
 # On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings:
 <blockquote>
@@ Line 13: / Line 14: @@
 == Starting the system ==
-# Connect the DC 12V power supply adapter (included) to main DC power connector '''J2'''.
+# Connect the DC 12V power supply adapter (included in the kit) to main DC power connector '''J1'''.
-# Follow the messages in your terminal emulator program until you see the linux shell command line prompt.
+# Toggle the main power switch '''SW1''' to '''ON''' position.
 {{note|In case of no messages appear in your terminal emulation program, please refer to the detailed [[SB-UCM-iMX8: HOWTO: USB Console|USB console]] guide.}}
 == What Next? ==