Igor at 14:09, 23 July 2023

2023-07-23T14:09:36Z

imported>Kirill.kapranov: /* Setting up your host PC */

2018-12-09T18:37:27Z

‎Setting up your host PC

New page

== Setting up your host PC ==
# Connect a micro-USB cable (included with the evaluation kit) between the SBC connector '''P13''' to a free USB port on your host PC.
# Make sure the CP2104 driver is available with your operating system, otherwise install CP2104 driver onto the host PC from here: https://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx
# Identify the host PC interface and port you will be using for communication with the SBC:
#* For Linux hosts, the serial port in most cases would be called like one of the following (where n is a positive integer): /dev/ttyUSB0, /dev/ttyUSB1 ... /dev/ttyUSBn
#* For Windows Hosts, the serial port in most cases would be called like one of the following (where n is a positive integer): COM1, COM2 ... COMn
# Start a terminal emulation program (such as HyperTerminal on Windows or minicom on Linux).
# Within the terminal emulation program, in the serial port configuration section select the port identified in previous step and set the following serial port parameters:
<blockquote>
{{:SB-SOM: serial port parameters table}}
</blockquote>


== Setting up the Compulab Board ==
# Make sure jumper '''E4''' is not populated.
# Start the system by enabling power through the main DC power connector.
# Console messages should appear on your host PC through the terminal emulation program.



[[Category:SB-UCM-iMX8]]

@@ Line 3: / Line 3: @@
 == Setting up your host PC ==
-# Connect a micro-USB cable (included with the evaluation kit) between the SBC connector '''P13''' to a free USB port on your host PC.
+# Make sure that the micro-USB cable is properly connected between the SBC console connector to a USB port on your host PC.
-# Make sure the CP2104 driver is available with your operating system, otherwise install CP2104 driver onto the host PC from here: https://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx
+# Make sure the CP2104 driver is available with your operating system, otherwise install CP2104 driver onto the host PC from https://www.silabs.com/documents/public/software/CP210x_Windows_Drivers_with_Serial_Enumeration.zip
-# Identify the host PC interface and port you will be using for communication with the SBC:
+# Identify the host PC interface and port number that will be used for communication with the SBC:
-#* For Linux hosts, the serial port in most cases would be called like one of the following (where n is a positive integer): /dev/ttyUSB0, /dev/ttyUSB1 ... /dev/ttyUSBn
+#* In most Linux PCs, the serial port will be denoted as one of the following (where n is a positive integer): /dev/ttyUSB0, /dev/ttyUSB1 ... /dev/ttyUSBn
-#* For Windows Hosts, the serial port in most cases would be called like one of the following (where n is a positive integer): COM1, COM2 ... COMn
+#* In Windows PCs, the serial port usually will be denoted as one of the following (where n is a positive integer): COM1, COM2 ... COMn
 # Start a terminal emulation program (such as HyperTerminal on Windows or minicom on Linux).
 # Within the terminal emulation program, in the serial port configuration section select the port identified in previous step and set the following serial port parameters:
@@ Line 16: / Line 16: @@
 == Setting up the Compulab Board ==
 # Start the system by enabling power through the main DC power connector.
 # Console messages should appear on your host PC through the terminal emulation program.
@@ Line 22: / Line 21: @@
 <!--'''More Details:''' ''[[SB-iMX8:_Connector:J2|main DC power connector]]'', ''[[SB-SOM:_Jumpers:_E4|E4]]''.-->
-[[Category:SB-UCM-iMX8]]
+[[Category:UCM-iMX93]]

SB-UCM-iMX8: HOWTO: USB Console - Revision history

Igor at 14:09, 23 July 2023

imported>Kirill.kapranov: /* Setting up your host PC */