CL-SOM-iMX8: Evaluation Kit: Getting Started - Revision history

imported>Igor.vaisbein: /* System setup */

2020-02-20T10:41:47Z

‎System setup

imported>Igor.vaisbein: /* Starting the system */

2019-08-06T08:02:55Z

‎Starting the system

Igor: /* System setup */

2018-01-09T12:17:12Z

‎System setup

New page

[[Image:CL-SOM-iMX8-eval-kit-quick-setup.jpg|800px]]


== System setup ==


# Connect a DVI/HDMI Display to HDMI connector '''J2''' using a standard HDMI/DVI cable.
# Connect a USB Keyboard to USB connector '''U30'''.
# Make sure jumpers '''E3''', '''E8''' and '''E11''' are not populated.
# Make sure jumpers '''E9''' and '''E10''' are populated (default state).
# Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector '''P12'''.
# On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings:
<blockquote>
{{:SB-SOM: serial port parameters table}}
</blockquote>

'''More Details:''' ''[[SB-iMX8:_Connectors:_J2|Connector J2]]'', ''[[SB-iMX8:_Connectors:_U30|Connector U30]]'', ''[[SB-iMX8:_Connectors:_P12|Connector P12]]''.

== Starting the system ==
# Connect the DC 12V power supply adapter (included) to main DC power connector - '''J3'''.
# Follow the messages in your terminal emulator program until you see the linux login prompt.
# Use the credentials below to login.
:* username: root
:* password: 111111
{{note|In case no messages appear in your terminal emulation program, please refer to the detailed [[SB-iMX8: HOWTO: USB Console|USB console]] guide.}}



== What Next? ==

* [http://www.compulab.com/products/computer-on-modules/cl-som-imx8-nxp-i-mx-8-system-on-module-computer/#devres CL-SOM-iMX8 development resources]

[[Category:SB-iMX8]]
[[Category:CL-SOM-iMX8]]

@@ Line 7: / Line 7: @@
 # Connect a DVI/HDMI Display to HDMI connector '''J2''' using a standard HDMI/DVI cable.
 # Connect a USB Keyboard to USB connector '''U30'''.
-# Make sure jumpers '''E3''', '''E8''' and '''E11''' are not populated.
+# Make sure jumpers '''E3''', '''E9''' and '''E11''' are not populated.
-# Make sure jumpers '''E9''' and '''E10''' are populated (default state).
+# Make sure jumpers '''E8''' and '''E10''' are populated (default state).
 # Connect a standard USB cable (included in the kit) between your host PC and the evaluation kit micro-USB2.0 connector '''P12'''.
 # On your computer, start a terminal emulation program (such as HyperTerminal) with the following serial port settings:

@@ Line 18: / Line 18: @@
 == Starting the system ==
-# Connect the DC 12V power supply adapter (included) to main DC power connector - '''J3'''.
+# Connect the DC 12V power supply adapter (included) to main DC power connector '''J3'''.
-# Follow the messages in your terminal emulator program until you see the linux login prompt.
+# The system will boot into Linux. Root auto-login is enabled on the serial console .
 {{note|In case no messages appear in your terminal emulation program, please refer to the detailed [[SB-iMX8: HOWTO: USB Console|USB console]] guide.}}
 <!--'''More Details:''' ''[[SB-iMX8: Connectors: J6 and J8|Connector J6]]''.-->
@@ Line 30: / Line 26: @@
 <!--* [[CL-SOM-iMX8 NXP i.MX8 U-Boot|CL-SOM-iMX8 U-Boot guide]]
 * [[CL-SOM-iMX8 NAXP i.MX8 Linux|CL-SOM-iMX8 Linux guide]]
 * [[CL-SOM-iMX8 NXP i.MX8 FreeRTOS|CL-SOM-iMX8 FreeRTOS guide]]
 * [[CL-SOM-iMX8: Evaluation Kit: Hardware Guide|CL-SOM-iMX8 evaluation kit hardware guide]]-->
 * [http://www.compulab.com/products/computer-on-modules/cl-som-imx8-nxp-i-mx-8-system-on-module-computer/#devres CL-SOM-iMX8 development resources]
 [[Category:SB-iMX8]]
 [[Category:CL-SOM-iMX8]]