Grinberg at 14:40, 4 June 2017

2017-06-04T14:40:51Z

Grinberg at 15:07, 3 May 2017

2017-05-03T15:07:19Z

Grinberg: /* Display */

2017-05-03T14:54:32Z

‎Display

New page

== Overview ==
<blockquote>

=== Terms and Definitions ===
{| border="1" cellspacing="1" cellpadding="3" style="border-collapse:collapse"
! align="center" | Term
! align="center" | Definition
|-
| Evaluation kit
| A combination of CL-SOM-iMX6 & SB-FX6 boards accompanied by a set of accessories detailed [http://www.compulab.co.il/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#evalkit here]
|-
| CL-SOM-iMX6
| A system-on-module product described [http://www.compulab.co.il/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#specs here]
|-
| SB-FX6
| A generic carrier board designed to support the CM-FX6 and the CL-SOM-iMX6 evaluation kits from Compulab.
|-
| SBC-iMX6
| CL-SOM-iMX6 populated on top of the SB-FX6 carrier board
|-
| SoM
| system-on-module
|-
|}

=== Reference Carrier Board ===
The evaluation kit is shipped with the SB-FX6 carrier board

The design materials for SB-FX6 (including schematics, PCB layout and Bill of Materials) are available for download from [http://www.compulab.co.il/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#devres here]

==== Additional resources ====
*[[CL-SOM-iMX6: Evaluation Kit: Getting Started|Getting started with CL-SOM-iMX6 evaluation kit]]

*[http://www.compulab.co.il/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#devres CL-SOM-iMX6 development resources]
</blockquote>

== Carrier Board ==

{| border="0" cellspacing="1" cellpadding="3" style="border-collapse:collapse"
|
[[Image:SB_FX6_topview2.jpg|550px|alt=SB-FX6 top view|<div align="center">SB-FX6 top view</div>]]
|
[[Image:SB_FX6_bottomview2.jpg|550px|alt=SB-FX6 bottom view|<div align="center">SB-FX6 bottom view</div>]]
|}

== Interfaces and Functions ==
=== Main Power ===
----
Connector '''J4''' is the main DC power source of this evaluation kit. The DC power supply unit included with the evaluation kit provides 12V DC power to the system through '''J4'''.

=== Serial Console ===
----
Serial console is available through one of the following interfaces:
* Serial over USB using micro-USB2.0 Type-B '''P20''' connector. Continue to [[SB-FX6: HOWTO: USB Console|USB console guide]] for USB interface setup instructions.
* Serial over RS-232 using the '''P60''' connector with custom RS-232 cable (included with the evaluation kit). Continue to [[SB-FX6: HOWTO: RS-232 Console|RS-232 console guide]] for RS-232 interface setup instructions.

=== USB ===
----
A total of 5 CL-SOM-iMX6 USB ports are accessible with this evaluation kit:
# CL-SOM-iMX6 USB2.0 OTG port is available through the OTG connector '''P48'''.
#* USB Host connection: The micro-USB to USB type-A adapter included with evaluation kit (available for purchase [http://www.compulab.co.il/support/cables-connectors-accessories/ here]) allows usage of connector '''P48''' as a standard USB2.00 host port.
#* USB Gadget connection: A standard micro-USB cable (included with evaluation kit) enables connection of the evaluation kit as a USB gadget to the USB port of your host computer.
# CL-SOM-iMX6 USB 2.0 Host Ports 1 through 4 are available through the following connectors:
#* USB2.0 Host port 1 (from CL-SOM-iMX6 onboard hub) is accessible through the bottom socket of P13 connector
#* USB2.0 Host port 2 (from CL-SOM-iMX6 onboard hub) is accessible through the top socket of P13 connector
#* USB2.0 Host port 3 (from CL-SOM-iMX6 onboard hub) is accessible through the bottom socket of P15 connector
#* USB2.0 Host port 4 (from CL-SOM-iMX6 onboard hub) is accessible through one of the following (depending on state of Jumper P31):
<blockquote>
<blockquote>
{| border="1" cellspacing="1" cellpadding="3" style="border-collapse:collapse"
! align="center" | P31 Setting
! align="center" | USB port 4 availability
|-
| 1-2
| USB Type-A (P15 top)
|-
| 2-3
| mini-PCIe (P40)
|-
| N.A.
| Controlled by Software
|-
|}
</blockquote>
</blockquote>

=== Ethernet ===
----
The kit features two 1Gbps copper Ethernet ports. While the first ethernet port is implemented fully onboard CL-SOM-iMX6 module, the second port is implemented onboard SB-FX6 using the PCI-Express port available with CL-SOM-iMX6. Both ports are exposed through the P9 Dual RJ45 connector.

<blockquote>
==== Primary Ethernet ====
The primary Ethernet port (also referred to as CM Ethernet, SOM ETH or Module Ethernet) is available through the left side of the dual RJ45 connector '''P9''' (also called ('''P9A''').

==== Secondary Ethernet ====
The secondary Ethernet port (also referred to as SB Ethernet, SB ETH or 2nd Ethrnet) is available through the right side of the dual RJ45 connector '''P9''' (also called '''P9B'''). The '''P31''' jumper setting determines whether the CL-SOM-iMX6 PCI-Express interface is utilized for the secondary ethernet port (Ethernet is available through '''P9B''') or for the '''P40''' mini-PCIe socket (Ethernet is not available through P9B) onboard SB-FX6.
<blockquote>
{| border="1" cellspacing="1" cellpadding="3" style="border-collapse:collapse"
! align="center" | P31 Setting
! align="center" | Secondary Ethernet port availability through P9B
|-
| 1-2
| Available
|-
| 2-3
| N.A.
|-
| N.A.
| Availability determined by Software
|-
|}
</blockquote>
</blockquote>

=== PCI-Express ===
----
The PCI-Express interface available with CL-SOM-iMX6 is shared between the secondary ethernet (through '''P9B''') and the '''P40''' mini-PCI-Express card slot.
'''P40''' availability of the PCI-Express interface is determined by the '''P31''' jumper setting as follows:
<blockquote>
<blockquote>
{| border="1" cellspacing="1" cellpadding="3" style="border-collapse:collapse"
! align="center" | P31 Setting
! align="center" | PCI-Express availability through P40 mini-PCIe slot
|-
| 1-2
| N.A
|-
| 2-3
| Available
|-
| N.A.
| Availability determined by Software
|-
|}
</blockquote>
</blockquote>

=== SATA ===
----
The Serial ATA (SATA) interface available with CL-SOM-iMX6 is accessible through one of the following connectors:
# P7/P63 SATA connector
# P40 mini-PCIe slot (mSATA)
<blockquote>

====Standard SATA ====
The Evaluation kit supports connection of standard SATA Mechanical and SSD drives to the system through the P7/P63 standard SATA connector. Support of the SATA drives is determined by jumper '''P31''' setting as follows:

<blockquote>
{| border="1" cellspacing="1" cellpadding="3" style="border-collapse:collapse"
! align="center" | P31 Setting
! align="center" | SATA Drives support on connector P7/P63
|-
| 1-2
| N.A.
|-
| 2-3
| Supported
|-
| N.A.
| Availability determined by Software
|-
|}
</blockquote>

==== mSATA ====
The Evaluation kit supports mSATA form-factor drives through the '''P40''' miniPCIe connector.
Support of the mSATA drives is determined by jumper '''P31''' setting as follows:

<blockquote>
{| border="1" cellspacing="1" cellpadding="3" style="border-collapse:collapse"
! align="center" | P31 Setting
! align="center" | SATA Drives support on mPCIe slot P40
|-
| 1-2
| N.A.
|-
| 2-3
| Supported
|-
| N.A.
| Availability determined by Software
|-
|}
</blockquote>
</blockquote>

=== CAN Bus===
----
CAN bus nodes can be connected to evaluation kit header '''P61''' as described in [[SB-FX6:_HOWTO:_CAN_Connection|CAN node connection guide]].

=== Wireless ===
----

<blockquote>

==== WiFi/Bluetooth ====
Connect the antenna (included with evaluation kit) to CL-SOM-iMX6 connectors J1/J2 for WiFi and/or Bluetooth operation.

==== Cellular ====
USB and/or PCI-express interfaced cellular modems (2G/3G/4G etc.) can be plugged into connector P40 (mini-PCI-Express) as explained below:

# Short pins 2 & 3 of header P31 with a jumper cap.
# Plug your modem into P40 mini PCI-Express connector.
# Insert your micro-SIM card into the P22 micro-SIM slot (only relevant if your cellular modem requires sim card access while not featuring an onboard SIM slot).

</blockquote>

=== Display ===
----
CL-SOM-iMX6 evaluation platform has built in support for 7 different connectors up to 4 of which can operate simultaneously.

<blockquote>
==== HDMI ====
The HDMI display interface is accessible through the HDMI connector '''J5'''. Default configuration of Debian Linux for CL-SOM-iMX6 uses HDMI as primary video output.

==== DVI ====
The DVI display interface is accessible through the HDMI connector '''J5''':
{{note|The DVI interface utilizes the Parallel Display Interface available with CL-SOM-iMX6. Simultaneous operation of TD035STEE1, the DVI interface and the HannStar HSD050IDW1/Startek KD050C-1A LCD panels is not supported since they use the same CL-SOM-iMX6 parallel display interface}}

==== LVDS 0 ====
The CL-SOM-iMX6 LVDS Display 0 Interface Signals are accessible through evaluation kit header '''P53'''.
This header enables simple connection (with jumper wires) to any LVDS panel.
Please refer to SB-FX6 schematics for detailed information on '''P53'''.

==== LVDS 1 ====
The CL-SOM-iMX6 LVDS Display 1 Interface is accessible through the '''P17''' FPC connector. '''P17''' is compatible with the NL10276BC20-12 LCD panel.
{{note|this evaluation kit does not provide backlight supply to the NL10276BC20-12 panel. NL10276BC20-12 backlight power must be provided externally}}

==== HannStar HSD050IDW1/Startek KD050C-1A LCD ====
Evaluation kit supports the HannStar HSD050IDW1 / Startek KD050C-1A LCD panels (one is included with the evaluation kit) through the '''P50''' dedicated FPC connector.
These LCD panels assembly is integrated with a resistive touch panel enabled by CL-SOM-iMX6 onboard resistive touch panel controller.
{{note|HannStar HSD050IDW1/Startek KD050C-1A LCD panels utilize the Parallel Display Interface available with CL-SOM-iMX6. Simultaneous operation of TD035STEE1, the DVI interface and the HannStar HSD050IDW1/Startek KD050C-1A LCD panels is not supported since they use the same CL-SOM-iMX6 parallel display interface}}

==== TRULY TFT480800-56-E REV 1.0 LCD ====
Evaluation kit supports the TRULY TFT480800-56-E REV 1.0 LCD panel through '''P19''' dedicated FPC connector.
The TRULY TFT480800-56-E REV 1.0 LCD utilizes the MIPI-DSI display interface available with CL-SOM-iMX6
</blockquote>

=== Touch Panel Interface ===
----
The CL-SOM-iMX6 resistive touch panel interface is accessible through the '''P58''' and '''P59''' headers. Any 4-wire resistive touch panel can be tested with the system by connecting to '''P58''' and '''P59''' through use of jumper-wires.

=== Camera ===
----
<blockquote>
==== Parallel Camera Interface ====
The Parallel camera interface signals (if available*) are accessible through one of the following interfaces (but not both simultaneously).
# '''P57''' Header - Designed to allow the flexibility of using jumper-wires allowing connection of any camera with a parallel interface.
# '''P62''' FPC connector - Enabling simple connection with the [[Video Input Port Adapter Board|VIP-ADP]] board
{{note|By default, some of the CL-SOM-iMX6 parallel camera interface signals are not available with this evaluation kit, please refer to CL-SOM-iMX6 reference manual for details}}

==== MIPI camera interface MIPI-CSI ====
The MIPI-CSI Camera interface is available through the '''P66''' dedicated connector. '''P66''' is compatible with the [https://www.leopardimaging.com/LI-OV5640-MIPI-AF.html Leopard Imaging LI-OV5640-MIPI-AF] camera module
</blockquote>

=== SD Card support ===
----
SB-FX6 allows access to up to 3 of the CL-SOM-iMX6 interfaces.
# SDIO1 (if available with CL-SOM-iMX6) is accessible through the '''P55''' micro-SD socket.
# SDIO2 (if available with CL-SOM-iMX6) is accessible through the '''P21''' header.
# SDIO3 is accessible through the '''P6''' full-size SD card slot.
{{note|Some of the SDIO signals are not available with CL-SOM-iMX6 evaluation kit (stock configuration of CL-SOM-iMX6 board). Please refer to CL-SOM-iMX6 hardware reference manual for signal availability details}}
=== Audio ===
----
<blockquote>
==== Analog Audio ====
===== Listening to Audio =====
# Plug your headphones into '''J3''' (AUDIO_OUT) audio jack
# Enable audio playback through the Analog audio interface (using software)
===== Recording Audio from Line-in =====
# Plug your audio source into '''J2''' (AUDIO_IN) audio jack
# Enable audio recording from the Analog audio line-in interface (using software)
===== Recording Audio from Mirophone =====
# Plug a standard PC Microphone into '''J1''' (MIC_IN) audio jack
# Enable audio recording from the Analog audio microphone interface (using software)
==== S/PDIF ====
===== Audio Playback through S/PDIF =====
# Plug your coaxial S/PDIF receiver to the '''P46''' COAX connector.
# Enable audio playback through the S/PDIF audio interface (using software)
===== Recording Audio from S/PDIF source =====
# Plug your coaxial S/PDIF source to the '''P47''' COAX connector.
# Enable audio recording from the S/PDIF interface (using software)
==== HDMI ====
# Plug your Television/or HDMI capable monitor (with speakers) into the '''J5''' HDMI connector
# Enable audio playback through the HDMI interface (using software)
==== I2S/PCM ====

</blockquote>

=== UART and RS232/RS422/RS485 ===
----
RS-232, RS-422 and RS-485 interfaces are available through the dual RJ11 connector '''P32'''.
The UART signals are Available through header '''P56'''.
CL-SOM-iMX6 UART1, UART2 and UART5 interfaces are utilized to support functions at '''P32''' and '''P56'''.

* The interface exposed through '''P32A''' connector (left side of P32) utilizes the CL-SOM-iMX6 UART2 interface. Either half or full duplex operation is supported through '''P32A'''. '''P32A''' operation mode, duplex and other settings are set by software.
* The interface exposed through '''P32B''' connector (right side of P32) utilizes either '''UART5''' or '''UART1'''. Only full duplex operation is supported through '''P32B'''. '''P32B''' operation mode and other settings are set by software.

{{note| UART5 signals are not available with this evaluation kit by default. Please refer to CL-SOM-iMX6 reference manual for details.}}
{{note| Some of the UART2 signals are not available with this evaluation kit by default. Please refer to CL-SOM-iMX6 reference manual for details.}}

=== Multifunctional signals access ===
----
The following headers allow access to multifunctional signals (if available) of CL-SOM-iMX6
# P56 (UART Header)
# P26 (Camera Header)
# P21 (SDIO2 Header)
# P18 (OTHER Header)
{{note|Please refer to CL-SOM-iMX6 reference manual for signal availability information}}
<blockquote>
==== SPI ====
CL-SOM-iMX6 SPI5 interface is accessible (if available) through the '''P21''' header.
CL-SOM-iMX6 SPI2 interface utilized for communicating and LCD panel with this evaluation kit. One can test SPI2 functionality using wire-up from connector '''P16''' or '''P50''' if LCD is not required.
{{note|The SPI5 interface signals are not available with this evaluation kit by default. Please refer to CL-SOM-iMX6 reference guide for details on signal availability}}

==== I2C ====
CL-SOM-iMX6 I2C1 bus interface (at 3.3V) is accessible through the P35 header.
{{note|Some of the I2C slave addresses must not be used when testing your I2C device with this evaluation kit since devices with these addresses are already populated onboard SB-FX6. Please refer to SB-FX6 schematics last page for details}}

==== GPIO ====
# Any multifunctional signal available through the CL-SOM-iMX6 carrier board interface can be configured by SW to function as a GPIO. It is recommended to use the multifunctional pins accessible through the SB-FX6 headers above (P56, P26, P21 and P18) to evaluate GPIO functionality.
# Additional, SB-FX6 implemented GPIO signals(eGPIO), are available through the P36 and P38 Headers.
</blockquote>

=== System ===
----
<blockquote>
==== Reset ====
Pressing the reset button ('''SW4''') triggers evaluation kit cold reset.

==== Boot Sequence Selection ====
Evaluation kit supports normal and alternate boot sequences. Detailed description of the sequences is available in the CL-SOM-iMX6 reference guide.
* Pressing and holding the ALT.BOOT button ('''SW5''') during power-up or cold reset forces alternate boot sequence (boot from SD card on SDIO3 interface).
* Populating the '''E1''' jumper, constantly forces alternative boot sequence.
* Indication of selected boot sequence is shown with the '''DS9''' LED.

==== ON/OFF button ====
* Pressing ON/OFF button ('''SW3''') generates a wake/power-on request.
* Pressing and holding (>5sec) '''SW3''' button results in system switch off.

==== RTC ====
The evaluation kit RTC (implemented onboard CL-SOM-iMX6) is powered by a coin cell battery. RTC power can be disconnected by removing the coin cell battery from BH1 battery holder.
</blockquote>

=== Jumpers Summary ===
----
<blockquote>
#'''E1''' - Boot Sequence Selection. Populate to force alternate boot sequence.
#'''E2''' - CL-SOM-iMX6 onboard EEPROM and bootloader storage write-protection. Populate to enable the EEPROM write protection and allow bootloader storage write-protection.

#'''E4''' - i.MX6 JTAG_MOD jumper. Populate jumper to place i.MX6 SoC into SW debug mode.
#'''E5''' - Console selection jumper. Populate to force RS-232 console through P60.

#'''P31''' - PCI-Express / USB port 4 / SATA interface / 2nd Ethernet availability selection jumper. Refer to respective chapters for details.
#'''P39''' - Li-Ion Charger disable jumper. Populate to disable Li-Ion battery changer.
</blockquote>
[[Category:SB-FX6]]
[[Category:CL-SOM-iMX6]]

@@ Line 31: / Line 31: @@
 ==== Additional resources ====
 *[[CL-SOM-iMX6: Evaluation Kit: Getting Started|Getting started with CL-SOM-iMX6 evaluation kit]]
 <!--
 *[[CL-SOM-iMX6 NXP i.MX6 Yocto Linux|CL-SOM-iMX6 Yocto guide]]
 -->

@@ Line 8: / Line 8: @@
 |-
 | Evaluation kit
-| A combination of CL-SOM-iMX6 & SB-FX6 boards accompanied by a set of accessories detailed [http://www.compulab.co.il/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#evalkit here]
+| A combination of CL-SOM-iMX6 & SB-FX6 boards accompanied by a set of accessories detailed [http://www.compulab.com/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#evalkit here]
 |-
 | CL-SOM-iMX6
-| A system-on-module product described [http://www.compulab.co.il/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#specs here]
+| A system-on-module product described [http://www.compulab.com/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#specs here]
 |-
 | SB-FX6
@@ Line 27: / Line 27: @@
 The evaluation kit is shipped with the SB-FX6 carrier board
-The design materials for SB-FX6 (including schematics, PCB layout and Bill of Materials) are available for download from [http://www.compulab.co.il/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#devres here]
+The design materials for SB-FX6 (including schematics, PCB layout and Bill of Materials) are available for download from [http://www.compulab.com/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#devres here]
 ==== Additional resources ====
@@ Line 35: / Line 35: @@
 *[[CL-SOM-iMX6 NXP i.MX6 Yocto Linux|CL-SOM-iMX6 Yocto guide]]
 -->
-*[http://www.compulab.co.il/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#devres CL-SOM-iMX6 development resources]
+*[http://www.compulab.com/products/computer-on-modules/cl-som-imx6-nxp-freescale-i-mx-6-system-on-module/#devres CL-SOM-iMX6 development resources]
 </blockquote>
@@ Line 62: / Line 62: @@
 A total of 5 CL-SOM-iMX6 USB ports are accessible with this evaluation kit:
 # CL-SOM-iMX6 USB2.0 OTG port is available through the OTG connector '''P48'''.
-#* USB Host connection: The micro-USB to USB type-A adapter included with evaluation kit (available for purchase [http://www.compulab.co.il/support/cables-connectors-accessories/ here]) allows usage of connector '''P48''' as a standard USB2.00 host port.
+#* USB Host connection: The micro-USB to USB type-A adapter included with evaluation kit (available for purchase [http://www.compulab.com/support/cables-connectors-accessories/ here]) allows usage of connector '''P48''' as a standard USB2.00 host port.
 #* USB Gadget connection: A standard micro-USB cable (included with evaluation kit) enables connection of the evaluation kit as a USB gadget to the USB port of your host computer.
 # CL-SOM-iMX6 USB 2.0 Host Ports 1 through 4 are available through the following connectors:

CL-SOM-iMX6: Evaluation Kit: Hardware Guide - Revision history

Grinberg at 14:40, 4 June 2017

Grinberg at 15:07, 3 May 2017

Grinberg: /* Display */